Hi there - setting up my new Blue series switches and am having some trouble getting my switches to respond lights as expected. Here’s the setup: Home Assistant Conbee II Zigbee Stick MagicLight Wifi Bulb Blue Series single pole with neutral wire The switch is set to smart bulb mode and “disable …

Also seeing the same issues except I’m using Z2M and Sonoff. I have a very simple HA automation that is set to toggle a hue bulb if the switch is double pressed. If it’s been more than a minute or two (maybe longer, I haven’t done any sort of scientific testing on the timing) the switch no longer se…

I’ve had similar problems, but a single up tap sometimes doesn’t do the trick to re-activate double-up taps. Sometimes I have to hit down first before anything else will work. Other times it has to be up before any down commands will go through.

Yeah it really feels like something in the switch is going to “sleep”. Hopefully this is all just a config issue since there’s such a variety of platforms people are using and not something related to the signal/routing/pairing issues mentioned in other threads. I tend to think not since my switche…

I’m in a similar boat. Every morning I wake up to Zigbee problems. A handful of my switches seem either go to sleep or become unavailable where they can’t be woken up remotely. This causes binding to break and also causes routing instability between other Zigbee devices. I have blue switches bound t…

[image] elaw611: Using HA and Zigbee2MQTT Coordinator: SONOFF Dongle P Coordinator FW: 20220928 Fill out the form: [image] Blue Series 2-1 Signal / Routing / Performance Issue Troubleshooting Thread General Discussion Hey all, In reading through some of these th…

@EricM_Inovelli – can you take a look at this when you have a chance (I know you’re buried with some of these other issues)? This seems to be an issue – I’m not sure if it’s related to the network/routing issues (ie: maybe commands aren’t being received due to network errors).

Further observations…it’s more random. Sometimes the double tap up event will work correctly even after the switch hasn’t been used in quite some time (like hours) but then sometimes it’ll just go right back to needing to be “awoken” with a tap up to turn on before it responds to double taps. I tri…

The one switch I had installed overnight timed out and marked itself unavailable (ZHA, ezsp on Sonoff bridge). Pushing a button on the paddle woke it up, and it rejoined. Smells like a zigbee problem I’ve seen in the past with some devices where they don’t handle monitoring clusters properly? Don’t…

I’ve don’t some testing over the last week and the switches continue to act randomly. I currently have 7 installed through ZHA with the following mix of log results from a simple “Up press”: No “ZigBee event” but the “switch light” turns on and the switch opening opens Both a ZigBee event and the …

Not sure if it’s helpful or not, but one of the five switches I set up this weekend would not send ZigBee events at first. I got the switch sending events by using the “Reconfigure” option in the ZHA device dashboard under “Device info”. As soon as that ran the switch started sending events on clic…

Inovelli Community

Blue 2-1 "Wake" needed?

Product Support

home-assistant, switches, zha, blue-2-1

dmulcahey November 8, 2022, 12:25pm 37

Blue Series 2-1 Switch - Enhancements/Bugs Thread General Discussion

[image] A colleague just pointed this out. This appears to be caused by a firmware bug. The events are being sent to destination endpoint 0 which is invalid as it’s the ZDO endpoint. These should be sent to a non zero endpoint id. The reason some folks work and some don’t is because the SI stack allows us to see the source endpoint and we can kind of hack it to fix it. The TI stack does not provide the source endpoint so the packet is interpreted as ZDO (which is what it is sent as unfortunat…

show post in topic

Home
Categories
Guidelines
Terms of Service
Privacy Policy

Powered by Discourse, best viewed with JavaScript enabled